2001 Chevrolet Corvette Keyless Entry Remote Fob Programming Instructions

Easy to Follow Step-by-step Key fob remote Programming Instructions

2001 Chevrolet Corvette

We strive to provide convenience to our customers with free keyless entry remote fob programming instructions for every single vehicle that we sell on NorthCoast Keyless.

Many people don’t know that they can purchase their own replacement vehicle entry remote, save up to 70% off of marked up Dealership prices, and program the replacement remote to their vehicle themselves. We know how good it feels to save money and do something yourself; and we aim to make it as painless as possible for you!

Free Key Fob Remote Programming Instructions for a 2001 Chevrolet Corvette


Time needed: 5 minutes.


KEY FOB REMOTE
Step-By-Step How To Programming Instructions

  1. Insert Key Into Ignition

    INSERT key into Ignition and TURN the Ignition to ON/ACC (just shy of cranking engine).

  2. Turn Radio Off

    TURN Radio OFF.

  3. Enter Programming Mode – Step 1

    PRESS the Driver Information Center (DIC) RESET button.

  4. Enter Programming Mode – Step 2

    PRESS the OPTIONS button on the DIC UNTIL the display is BLANK.

  5. Enter Programming Mode – Step 3

    PRESS and HOLD the RESET button for 3 seconds.

  6. Enter Programming Mode – Step 4

    PRESS the OPTIONS button until “FOB TRAINING” is displayed on the DIC.

  7. Enter Programming Mode – Step 5

    PRESS the RESET button to ENTER Programming Mode.

  8. Program Remote

    PRESS and HOLD BOTH the LOCK and UNLOCK buttons at the same time on the first remote for 15 seconds. A message will appear when the remote is successfully programmed.

  9. Program Additional Remotes

    REPEAT Step 8 for any additional remotes to be programmed, including existing ones.

  10. Exit Programming Mode

    TURN Ignition to OFF position and REMOVE key to EXIT Programming Mode.

  11. Test Remotes

    TEST all remotes. Programming is complete.

  12. Share

    If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Programming Notes:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
  • You may clear your keyless entry system memory by entering programming mode as shown in the steps above.

If you have any difficulties with programming your vehicles, contact us at [email protected].

Key fob remotes

2001 Chevrolet Corvette

OEM Electronic
Memory 1
OEM Electronic
Memory 2
NorthCoast Keyless Free Programming Instructions Disclaimer:
  • We worked hard to provide these instructions to our customers. We checked multiple sources to ensure that this information is complete and accurate. However, please understand that we cannot be held liable for any loss due to incorrect use of the programming instructions from www.northcoastkeyless.com.
  • If you cannot program your remote with the instructions that we provide or encounter any discrepancies, please contact us at [email protected] and we’ll make sure that you’re taken care of.

2 thoughts on “2001 Chevrolet Corvette Keyless Entry Remote Fob Programming Instructions

  1. Wendel says:

    I recently purchased a second remote keyfob for my 2001 chevy corvetee c-5. It worked for about a month, but no longer. I have replaced the battery and tried re-programming it to no avail. The originial keyfob (unit 1) was severly damaged.
    I went to the dealer and had this one tested by the parts department, to no avail. Do I need a new keyfob (if so I will order it from you) or other transmitters?

Leave a Reply

Your email address will not be published. Required fields are marked *